Does TCM310 have a teach-in function?

Does TCM310 have a teach-in function? This article applies to:DolphinAPI QUESTION Does TCM310 have a teach-in function? ANSWER No, as a gateway is has no teach-in. But if all you need to do is to filter out certain kinds of messages, you can use the filter command of ESP3. This can be done in the following manner: The teach-in procedure […] Read More

WAKE pins do not work on EVA300 and TCM300/TCM320

WAKE pins do not work on EVA300 and TCM300/TCM320 This article applies to:EVA300, TCM300, TCM320 QUESTION I wrote a custom firmware on TCM300 but I am unable to wake the module using the WAKE pins on the EVA board. What am I doing wrong? ANSWER The WAKE pins and several other pins are not available on TCM300/TCM320 modules. See user […] Read More

Problem when receiving telegrams from TCM300 through the serial port using EVA300

Problem when receiving telegrams from TCM300 through the serial port using EVA300 This article applies to:TCM300/TCM300C Module QUESTION I cannot receive any telegram through the serial port. I also cannot see any information with Winetel/DolphinView 2.0.0.0. ANSWER Make sure the ID table is cleared (press the CLR button for 3 seconds) Make sure the Mode0/1 is selected using the jumpers, […] Read More

How can I use the flywheel timer?

How can I use the flywheel timer? This article applies to:STM300 QUESTION I need a very precise timer for synchronous networks. I heard I could use the flywheel timer for this purpose. How to do it? ANSWER To use the flywheel Timer you will need a Wrist Watch Christal, we recommend the CM200CIn order to evaluate the flywheel timer on […] Read More

STM300 sends no telegram when pressing WAKE0/LRN button

STM300 sends no telegram when pressing WAKE0/LRN button This article applies to:STM300 QUESTION I am using STM300 module with EVA320. I have just unpacked this module put to the EVA board. I am using the default firmware and haven’t changed anything. When I press the WAKE0/LEARN button nothing happens. When I press WAKE1 button I see telegrams, why? ANSWER The […] Read More

PID and VID of EnOcean USB 300 – FTDI Chip configuration

PID and VID of EnOcean USB 300 – FTDI Chip configuration This article applies to:All EnOcean devices with FTDI chip QUESTION How I can change USB specific values (e.g. PID/VID) of the USB 300?How can I recognize an EnOcean Module connected to the host (e.g. PC)? ANSWER EnOcean is using FTDI’s FT232 chip within USB 300. Since this product is […] Read More

Smart Acknowledge Learn Modes

Smart Acknowledge Learn Modes This article applies to:Smart AcknowledgeDolphinAPI Version: 2.2.3.0 and later QUESTION What are the Learn Modes of Smart Acknowledge and how should I use them? ANSWER Smart Acknowledge has 3 Learn modes: Simple Mode – Learn Sensors only with direct radio contact to controller. Use this mode when you do not want to enable repeaters as possible Post […] Read More

How to integrate EnOcean USB 300 / Programmer with host controllers.

How to integrate EnOcean USB 300 / Programmer with host controllers. This article applies to: All Enocean Dolphin based devices with with FTDI chip QUESTION How can I use USB 300 / Programmer with Microsoft Windows? How can I use USB 300 / Programmer with Linux? ANSWER USB 300 and EnOcean Programmer (EOP) have both and FTDI Chip which enables the […] Read More

No FTDI Drivers Found

No FTDI Drivers Found This article applies to:DolphinView, DolphinStudio QUESTION I have installed DolphinView or DolphinStudio. I have selected the checkbox to install or update FTDI drivers during installation. Still after plugging in the EnOcean Programmer I get a Driver messagebox (see picture below) that the drivers where not found. What to do now? German English ANSWER On some Windows […] Read More